News:

2box forum: accident-free since the last one.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Topics - TheROTH

#1
Can anyone tell me what the Drummit-3 MIDI or input is for the following:

Snare Drum - RIM

Ride Cymbal - BELL


I have a DDT MS-140 E-Snare and a Yamaha PCY-155A 3-zone cymbal, being used as a ride.

If I can get this bit sorted, I stand a chance of actually seeing it in Superior Drummer 3, which obviously I don't!

I don't even know where to look for these inputs in the selections.
#2
Anyone know how to get the snare-drum rim-shot from Drummit-3?

I just can't seem to generate it at all.

Is there something wrong in my Unit or Kit settings?
#3
What settings do I use in Drumit-3 for a Roland RT-30HR trigger?

What type?  I don't know if it's Piezo/Piezo, Piezo/Switch, or what.

I am struggling to get any rim shot sounds in my 2Box.  Is there some setting for this?

How many zones are allocated to a snare, to include the rim shot?

And before anyone asks the obvious - yes, I am using a 'stereo' TRS cable.
#4
Is the RT30-HR compatible with 2Box Drummit-3?

If so, what settings for 'type' of input?
#5
I have 3 really good sounds I have downloaded from 2Box Sounds Library.

HOWEVER, having been recommended a certain software to convert them from DSND to .wav, but the software was riddled with viruses and have had my money returned.

Anybody know who can convert DSND to .wav please?
#6
I use a Pearl ePro TruTrac head on my snare.

I have never seen a place where you can adjust the rim-shot's on Drum-It 3

I would be grateful if someone can point out here or whereabouts in the manual this is.

I just want to adjust setting for the rim-shots just as I can with the main head.

Also, what pad setting would it be for the Pearl (ePro) Tru-Trac head?

I use these TruTrac heads on my snare (and Kick) as I struggle to get a good snare drum roll on mesh, whereas the toms 'dont matter' so much.
#7
General 2Box Drumit 3 Forum / Toontrack EZ Drummer 2
September 30, 2018, 04:59:26 PM
Has anyone rigged up their Drum-It 3 to Toontrack EZ Drummer 2 yet?

I assume this is over a MIDI?

Either way I'd be grateful for some configuration assistance.
#8
Anybody trying to get each individual drums/cymbals from their 2Box Drum-It 3 to multi-channel audio-interface (in my case a Focusrite 18i20) so can have visibility on Pro-Tools for each drum/cymbal?

Obviously there are only 4 analogue outputs (possibly 2 more via Phones sockets) and isn't really enough for sound engineering in (say) Pro Tools.

Love some advice on this and what other equipment I may need, if any solution available.
#9
General 2Box Drumit 3 Forum / Drum-It 3 Manual
September 22, 2018, 11:10:27 AM
Has anyone tries to adjust Zones for individual items?

I go in to UNITS then scroll down to INTF and in particular, looking at ZONES.

On my Snare is has ONE zone.  Yet, according to the online manual page 45, the PadP snare has TWO zones.  If I want to have TWO zones shown for my Snare, I have to select PadSS - and in the manual, the chart says that this particular pad is THREE zones.

Which is right and which is wrong?

Totally confused by 2Box manuals.
#10
Anyone know if the Pearl Tru-Trac heads (ePro) work with DrumIt3?
#11
General 2Box Drumit 3 Forum / Cymbals - Spinning Round
August 28, 2018, 02:06:38 PM
Does anyone know of a way to stop those quiet cymbals from 'spinning round'?

I have the perforated cymbals (loads of holes in, you know!), with triggers mounted on them.

Trouble is, they keep spinning round and the trigger will work its way to the back and elsewhere.  I just need the consistency and remain more or less in one place!
#12
Is there a way of importing individual drums/cymbals in Sound/Kit Editor software?

I just can't seem to select an external drum or cymbal to add to a kit.

Moreover, importing Enerd's kits also not happening.

Have to say, the DrummIt 3 manual is not very well written.
#13
General 2Box Drumit 3 Forum / Download kits?
August 25, 2018, 02:38:43 PM
Anybody know if there is a place where I can download full kits (or even individual drums/cymbals) for the DrumIt 3?