Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - VktoriusWarrior

Pages: [1]
1
Hi there guys,

I use a Drumit 3 module on Roland TD-25 hardware. I use it to play in a cover band. I've had the module for a year and half now.

Sometimes when I am playing live, I experience weird triggering (especially with the snare). One particular venue has a 'floating' stage. I feel like it might be the small movements of the stage that are screwing me up.

I will hit the snare, but the sound might be on time or late. It makes me sound like I'm playing like crap.

I have fiddled a little with the 'mask' setting a little bit when I was playing live. I think it might have helped a bit. But I didn't want to get too deep into playing with settings while in a live setting. On the other hand, I will only experience the problem when I'm playing live. I don't run into the problem when practicing.

I have also suspected the deep frequencies of our sub woofer or the bass player's amp being too close to my set and they are triggering some of the pads.

Has anybody else experienced something like this?

2
Hi there guys. I have a Drumit 3 module and I hope somebody can help me. I've done as much research, reading and fiddling with unit as I can, but I just can't figure this out.

I would like to use the "Split Wav" feature so that my module can play a song and send the "song" portion to the mixer and I can still have a click in my headphones.

I've got that figured out just fine, but the problem is that it doesn't seem like you can't adjust the volume of either those signals separately from one another. What I really want is to make the click track louder.

I don't know of any way of doing that, so another solution might be to have only have the click track side of the audio file (the manual calls this the metronome) in the headphones.

With that solution I would be able to hear my drums and the song in my floor monitor. Is there any way I could isolate all other sounds so I could hear ONLY the click in my headphones? (and the drums and song go to the outputs?)

The problem appears to be you can only have one 'sub mix'. I need a sub mix where the drums and the 'song' portion go out to the mixer (easy). But I also need a sub mix that disables everything but the metronome. I feel like if I could have 2 different sub mixes I could accomplish what I was trying to do.

Any help would be much appreciated.

3
General 2Box Drumit 3 Forum / Roland TD25 - Discouraged / Need Help
« on: March 21, 2019, 02:00:59 PM »
Hi there,

I purchased a Drumit 3 module to use with my Roland TD25 hardware back in the fall. I can hold my own with a lot of technical stuff, but I have found the learning curve to be quite high. I primarily use my kit for gigging.

I have got the basics down, but I think I need help with getting the best out of it. I spent a LOT of time trying to figure things out and I got to a certain level and then just sort of stalled in discouragement.

Now I feel like I have to give it another solid try before moving on. Here are my issues:

1. Although it's not a 2box problem, I have been discouraged to find that sounds on my computer (VSTs) are VERY different when using the SDSE tool from Lustark. The end result (playing the sounds on the module) don't seem to resemble the original sound at all.

2. It sounds like there has been lots of threads on the TD25 and the Drumit module, but I was wondering if anybody could speak up and say "I am using the TD25 and here are the parameters I use..."
I know that this is somewhat subjective because of different play styles etc., but I feel like I need to go back to some 'base' settings that work for the TD25 and then tweak from there.

3. If nobody responds to my point #2, perhaps somebody could help me with a more specific problem. When I am playing live, I find that my snare can get 'lost' in the mix of everything. It's almost like the cymbals or all the other sounds take precedence and one snare hit will not really trigger. Then it will come back to normal for the next hits. I know this is probably one setting (and it's probably a basic one), but I just don't know what it is.

4. I got close to figuring this out once, but now I have to revisit this to get it right. I need a dependable snare with a cross-stick sound that triggers properly. How do I do this again? I think it has something to do with having the snare sound at higher velocities, and the cross-stick sound at lower velocities...

Thanks in advance for any input.

EDIT: I suppose I should also add to point #3, that I really like snares that 'crack' when hit. So that is the sound I like going for. Not sure if the settings make a difference when trying to go for that sound

4
General 2Box Drumit 3 Forum / Hihat 'open' sound when I change kits
« on: October 12, 2018, 03:55:12 PM »
Hi there,

I consider myself a new drumit 3 module user. I'm using a Roland TD-25 kit with the Drumit 3, so that means I'm using a VH-11 hihat.

I was wondering if anybody else has experienced something similar to what I have. When I change kits, the hihat sound will play like it's open even though I have my foot down on the hihat pedal. After I let it up and press down again, it operates as normal.

I'm not sure if it's an error on my part calibrating it. Any input would be appreciated. Thanks.

5
General 2Box Drumit 3 Forum / SOLVED: Mount for the Drumit 3
« on: September 17, 2018, 06:14:09 PM »
Hello everybody,

I am a new drumit 3 module user. I've had the module for a couple of weeks now, and I'm enjoying it despite some of the learning curve (which I was expecting).

My main motivation for purchasing the module, was because I have a Roland TD-25 kit and I was getting tired of the sounds.

One thing I wanted to get a better sense of before my module arrived was "How was I going to mount it?". I couldn't seem to find any good (or recent) information on that topic. Even the forum posts seemed old or not applicable to the drumit 3.

The day it arrived, I took a look at it and saw the 4 screws at the back...but nothing else to assist with mounting it to a rack. I got thinking about fabricating something myself. But then I remembered my Alesis SamplePad Pro, and the special mount I purchased for it. I did some measurements and I figured out that lo and behold...the mount fit the drumit 3 module PERFECTLY. The dimensions were precisely the same!!

So I will share the link to the mount I purchased. I hope it helps other people try to do the same thing I did! Good luck.

https://www.amazon.com/Alesis-Electronic-Percussion-ControlPad-PerformancePad/dp/B003ZVBO8I/ref=sr_1_1?ie=UTF8&qid=1537207669&sr=8-1&keywords=alesis+module+mount


Pages: [1]