From http://2box-drums.com/support/
OS 1.34.10 Jan 10 2020
This OS is compatible with DrumIt5 and DrumIt Three.
* If a Hihat Calibration is performed the new calibration can now be saved in the UNIT file (Press UNIT-SAVE?).
* Fixed the issue with hihat opening value on kit change - now the opening value remains the same as stored in a KIT. (Finally!!!!)
* Added auto-set of decay value to "INF" in case a loop sound is selected for a channel.
* Cymbal choke is now active when a "HOLD" value is activated.
* A Crosstalk ( XTLK ) feature is added for Tom and Snare Channels to minimize crosstalk between Head and Rim.
Good news!!!
It is great OS version! The xtalk function between head/rim is a very good improvement for the users that experienced problems in the previous version with the separation and ghost notes.
Best regards
Anders / www.zourman.com
This prolly applies to very few users .... but I did the OS update yesterday on my D3 and D5 modules. On the D3 I did the HH calibration and that went fine, showing DONE. But when I would move the pedal NOTHING happened .... So, just as a reminder: Because the New OS remembers your previous HH settings: I had been using my Aux HH on the D3 as a Fixed Hat with a certain degree of openness .... I had to go to where I had set it as Fixed and change that .... then everything worked as expected .... That stumped me for a little while ;D
I think the new Xtalk settings for Head/Rim articulations are better. I haven't done a lot of experimenting with it yet, but initially it seems to work better than the previous LXTR Xtalk settings.
:-) The fixed hh pedal setting can really make you go bananas...seeking errors...
I think all settings are stored in each dkit file nowadays.
There is a manual up on the website for the new xtalk function:
http://2box-drums.com/wp-content/uploads/2020/01/Crosstalk-manual-for-OS-1.34.10.pdf
Best Regards
Anders / www.zourman.com
I have the jman conversion system with vh11 that works fantastic im still running the previous OS will I run in to problems (new calibration) because it works fine now. but I am thinking about a 2box trigit on ebay to have a acoustic snare conversion and for what I read in the new manual this could be good idee to have the new OS.
greetings
Frank
Quote from: rush1234 on January 16, 2020, 09:33:39 PM
I have the jman conversion system with vh11 that works fantastic im still running the previous OS will I run in to problems (new calibration) because it works fine now. but I am thinking about a 2box trigit on ebay to have a acoustic snare conversion and for what I read in the new manual this could be good idee to have the new OS.
greetings
Frank
I did the OS update as stated above and tested with my 2Box HH stand conversion kit. It worked for both the D3 and D5 modules with no problem.
Quote from: ANGR77 on January 13, 2020, 08:02:11 PM
It is great OS version! The xtalk function between head/rim is a very good improvement for the users that experienced problems in the previous version with the separation and ghost notes.
Best regards
Anders / www.zourman.com
Unfortunately not to me. I am only able to get perfect results on my 10 inch tom with the new xtalk function, 12 and 14 inch head frequently triggers the rim. I checked the manual to try different settings (LP/HP). Back to 1.32.4 gives no problems LXTR set vHigh.
Diamond drums with center piezo moved to the side (still mounted on the plastic disc) using drumtec design 2-ply mesh.
Quote from: Nico on January 20, 2020, 08:07:34 PM
Unfortunately not to me. I am only able to get perfect results on my 10 inch tom with the new xtalk function, 12 and 14 inch head frequently triggers the rim. I checked the manual to try different settings (LP/HP). Back to 1.32.4 gives no problems LXTR set vHigh.
Diamond drums with center piezo moved to the side (still mounted on the plastic disc) using drumtec design 2-ply mesh.
Did you also try this?:
X-ADJ: Boosts the Trigger preference for the current sensor (Head/Rim) if X-TLK sound is triggered on
Head/Rim
Quote from: Jman on January 20, 2020, 08:21:29 PM
Did you also try this?:
X-ADJ: Boosts the Trigger preference for the current sensor (Head/Rim) if X-TLK sound is triggered on
Head/Rim
Hi, yes I played with these adjustments (to max 12db) on head and rim. I believe boosting the head would be required in case the unwanted rim sound is heard.
Few weeks later OS1.36.1 already available but no improvement on x-talk head/rim. Keeping 1.32.4...
There where a couple of bugs fixed in 1.36.1 and some kind of adoption to 2box OEM vendors...
Best regards
Anders / www.zourman.com
Quote from: ANGR77 on February 13, 2020, 11:22:19 PM
some kind of adoption to 2box OEM vendors...
Sorry, I don't understand what you mean
Quote from: Jman on January 20, 2020, 08:21:29 PM
Did you also try this?:
X-ADJ: Boosts the Trigger preference for the current sensor (Head/Rim) if X-TLK sound is triggered on
Head/Rim
We need more clarification as to what this X-ADJ does since it's in dB... Boosts the trigger preference I think they meant increase the volume of the current sensor.
Also one thing I notice is you cannot turn on the rim x-tlk if the head x-tlk is off. Once head x-tlk is on, the rim x-tlk turns itself automatically on.