G'day all,
I've just been reading through old posts here and I haven't found a solution to my problem.
I just got my kit and I can't work out how to reliably trigger the cup.
If I hit it lightly then I it triggers sometimes but mostly it just makes a full cymbal sound.
The 2Box software triggers each zone exactly the way I want my cymbals to trigger.
How do I get my cymbals to trigger like switches ?
Tony
Quote from: 6828 on October 23, 2011, 12:11:38 AM
G'day all,
I've just been reading through old posts here and I haven't found a solution to my problem.
I just got my kit and I can't work out how to reliably trigger the cup.
If I hit it lightly then I it triggers sometimes but mostly it just makes a full cymbal sound.
The 2Box software triggers each zone exactly the way I want my cymbals to trigger.
How do I get my cymbals to trigger like switches ?
Tony
To start with you should check your OS, if it is not 1.20 you should update the OS ..... that helps. But if you play light bell hits it is normal to get bow sound. The Bow/Bell is not a Piezo/Switch .... or Switch/Switch .... etc .... it is just a single Piezo and sounds are Velocity switching .... IE strongest hits trigger bell sounds. If you set the Sensitivity high enough that light hits to the bell trigger the bell sounds, Hard hits to the bow will probably trigger bell sounds also. Just the nature of the beast IMO.
Thanks for the reply.
I've reset the brain and it was, and still, is running 1.2 and things are getting better but still not as accurate as I'd hoped.
I'll have a go on the sensitivity setting and see what I can achieve.
Cheers.
Tony
This is from the OS 2.0 Manual:
Cymbal triggers (UNIT-TRIG)
When the TYPE is Cym12/14, the GAIN parameter has an extra cup value selectable between
Low, Medium or High. First turn GAIN so only hard hits on the bow or edge give full level on
zone 4 or 8 (all LEVEL bars lit). Then click GAIN so only hard cup hits give full level on zone 1.
(Note: only relatively hard cup hits will result in zone 1, otherwise they result in zone 4.)
So that pretty much tells you what to expect ....
Had the same problem, check my answer on this topic:
http://www.2box-forum.com/index.php/topic,1074.0.html
Solution found.
Jman's suggestion worked.
Since it's a bit hard to navigate around on the Brain at times I've put together a little visual guide below to help future users that strike the same problem.
Press the
UNIT button to get into the setup system.
When you see this screen tap the
PAGE DOWN button once.
You should now see a screen where it says
TRIG on the side like this:
Now tap any of the
CYMB buttons.
Press down on this knob.
So that the letter reads
"M" next to the
GAIN number
This should now make the Cup/Bell ring with a firm but not necessarily hard hit.
Hope this helps you it certainly helped me ;) !
If it works for you,
SAVE the changes by pushing the
PAGE UP button then this button once.
Tony
Great work this visual guide
Huge difference ! thx
Waouu! Many Thanks!!
I never understood that when I was reading the new OS 1.2 manual!
Quote from: 6828 on October 25, 2011, 11:05:09 AM
Solution found.
Jman's suggestion worked.
...
Tony
Hey, nice guide, I've copied & stickied it here (http://www.2box-forum.com/index.php/topic,1077.0.html)
why is xtalk set on high?
Quote from: roel on November 05, 2011, 10:27:19 AM
why is xtalk set on high?
I prefer it on this as it is the least likely setting for cross triggering of the other triggers. :)
Tony
jeez thats a nice looking finger
Quote from: Spazo on November 05, 2011, 01:47:43 PM
jeez thats a nice looking finger
Thanks mate.
I'm available for professional hand modeling, just speak to my Talent Manager ;)
Tony