Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Jman

Pages: [1] 2 3 ... 127
They are even compatible with Drumit5  8)
To a point, major differences are the way the cymbals and Hi Hat are handled. The Hi Hat will only work with my Stealth 2Box HH Stand Conversion Kit or Zourman's box. Crashes are simple enough when set to PS or CyEdg type they will trigger Bow/Edge/Choke just like on the Roland module. But 3 zone Ride you would use the Bow/Bell input of the cymbal and set it to CyCup if you have a 2 jack Roland type Ride and you will get Bow/Bell ... no edge or choke.

Newbie here - I just heard about 2box 3 and 5 over the weekend. I spent hours on YouTube checking out these amazing products. I’m playing a set of Roland mesh heads with the expanded TD9 module.
Are they compatible with the Drumit 3?   Thank you.

I still have plenty of stock on the Stealth 2Box 32GB mod kits. Every card and extender is tested and verified plug n play ready. You just do the simple mod, plug in and go. These have the latest OS, and all the newest kits and sounds, which amounts to about 3GB more sounds already than you can fit on the stock module.... with lots of gigabytes of open card space for adding more.
Now .... Additionally, if you want, I will add the new eNerd kits to the card as detailed here: I have also added all the extra new kits sounds from the Drumit Three to the Drumit Five! ..... And Vice Versa ..... All the 2Box sounds that are available on both modules plus the net are on the card.
That gives the card a total of about 16GB of kits and sounds just to start on either module. The new kits reside on the card in alphabetical order after the 100 original 2box kits on the module.
Just send me a PM or email if interested, let me know if you are in the US, or where you are located. J

I have plenty of stock on these Stealth 2Box Hi Hat Stand Conversion kits and ship worldwide. I build and test every one personally, guaranteed to work. Just send me a PM or email if interested. Let me know if you are in the US, or where you are located. Jerry

Unfortunately, no amount of 'turning them up' makes them loud enough. It is chalk and cheese. Look at the last photo I posted. When I dropped that Ride into the first cymbal slot, I had to turn it down.

But now I am going to tell you something that will hurt your brain. ;)

I tried the editor on my PC. I put the card reader in and setup the software.. And . . .

All the sound work fine!!!!

Now I am confused. ALL the china cymbals work. The crashes I listed below work fine on my PC..

Just not on my LAPTOP!!..  I want them on my laptop as I travel over an hour each way to work every day.. What better way to spend the time than to work on kits and sounds.

I restarted the laptop and the problem persists.

What the???

Yeah, so I am just pointing out, all of the sounds you mention have been in use for years with other 2Box modules. So whatever the problem it is on your end... not the sound files.

As far as the Monitor levels. Those are all .dsnds from 2Box and that is their levels. If you want them louder you can just turn them up on the Monitor volume level. Many of the sounds are from the free downloads from 2Box, eNerd, and others are from the Drumit Five module content. In other words all the available sounds that are not already on the Drumit Three module. I did not adjust any levels those are all original.

Ok. I have gotten to the bottom of this, sort of.

I have the jman 32gb mod done.

In the 'China' folder there are 6 china type dnsd files.

Of these, these ones work

AZ 16 China
AZ 20 China
RB 21 Holy China
Swiss L 16 China

These next 2 do not work. (ie: very very low level)
SP Trash

Of the crashes I'll just list the ones that are not working

DnB1 Crash 1
DnB1 Crash 2
EU 14 to 18 (none of these work properly)

Could someone else with the Jman 32gb mod try some of these dsnd files and report back.
Not sure what you are experiencing, I just took one of the same cards loaded with those files plugged all the Chinas and Crashes, etc. you mention not working and they all work fine both in the Editor and the module?

General 2Box Drumit 3 Forum / Re: Module problem?
« on: November 22, 2018, 04:58:44 AM »
I noticed in the earlier post you mentioned the "Last thing" you were going to test is just through the headphones. Personally this is the first thing I would have done. Test through headphones connected directly to the module ..... Just sayin ....  ;)

General 2Box Drumit 3 Forum / Re: Module problem?
« on: November 18, 2018, 05:54:43 AM »
Whe playing the ride and kick simultaneously, the ride decays as though it’s being cut off. Also happens when playing the snare and ride together. Doesn’t happen with any other pads, ride rings and decays correctly. I have swapped cables, changed samples, adjusted settings etc. but to no avail. Anyone else experience this or any ideas?
You might want to turn the Crosstalk to Off for the Ride if you haven't already. I doubt that is it because normally you will just get missed hits AFAIK when it is a crosstalk issue, but it is worth a try.

e-drum DIY / modifications / Re: Cable snake be gone
« on: November 16, 2018, 04:16:50 PM »
Your kit looks great.
I opted out of putting my cables inside the rack. 1st, with the size of my kit I'm not sure they would all fit, LOL. 2nd and more important for me ..... I have replaced probably 6 or more cables in the last year alone. Not something I would want to do if they weren't easily accessible. I use corrugated wire channel on the inside of the rack tubing, which keeps things tidy and for the most part out of view.

General 2Box Drumit 3 Forum / Re: Problem 2box drumit 3 sound is disappear
« on: November 10, 2018, 10:27:08 PM »
Hello,i have some problems with 2box drumit 3. The problem is ,while im playing  drums sometimes the sound is disappear. And after some second there are playing many sounds that was disappear before. So what we should do with this problem?
I'd normally say to do a search because there are numerous threads about this subject, but you don't really even need to search because if you look you will see two other topics the 3rd and 4th ones in this Drumit Three Forum about the same subject.,3954.0.html

General 2box Drumit 5 forum / Re: Using with a Roland module
« on: November 10, 2018, 05:55:04 AM »
You prolly should look into the Owner's Manual as there is info on how the MIDI works with the Di5. And it also has the note numbers that 2Box assigns to the various instruments on pages 14-15.

General 2Box Drumit 3 Forum / Re: Adjusting Rim Settings - WHERE?
« on: November 09, 2018, 11:28:09 PM »
I use a Pearl ePro TruTrac head on my snare.

I have never seen a place where you can adjust the rim-shot's on Drum-It 3

I would be grateful if someone can point out here or whereabouts in the manual this is.

I just want to adjust setting for the rim-shots just as I can with the main head.

Also, what pad setting would it be for the Pearl (ePro) Tru-Trac head?

I use these TruTrac heads on my snare (and Kick) as I struggle to get a good snare drum roll on mesh, whereas the toms 'dont matter' so much.
Tru-Trac are Piezo/Switch type. So you pick PadPS for the pad type.

General 2Box Drumit 3 Forum / Re: D3 sounds pausing
« on: November 08, 2018, 04:00:59 PM »
I just wanted to add here. A number of people that had the bad "Intenso" card have ordered my 32GB card mod kit and their modules are working great now. But I would suggest you still contact 2Box to at least have a good Original 4GB card sent to you. It is always good to have the original card. And this mod is not being advertised as any kind of "Official" repair ...... LOL .... And while my Stealth 2Box Card Mod Kit installation is the same procedure as changing the original card any mods to the module are always at own risk. Jman

General 2Box Drumit 3 Forum / Re: D3 sounds pausing
« on: November 07, 2018, 11:52:13 PM »
I've had my D3 for about a month and it sounds brilliant. The problem I'm getting is after every few minutes of playing the sounds stop for about half a second and then all play at once. Is this a problem with the module or can I alter a setting to stop this?
Sounds like you have the Intenso SD card in your module. Already documented on the forum, a bad card that needs to be replaced. Do a search and you will find other posts about it.

Pages: [1] 2 3 ... 127